show maestro

This command is supported only on:

  • Maestro Orchestrator

Note - You must run this command in Gaia Clish.

Description

Shows settings on the Maestro Orchestrator.

Related Commands

Syntax

show maestro[Esc][Esc]

show maestro auto-scale

      interactive-rules

      interactive-status

      scale-units

      security-group-id <ID>

            scale-down-rules

            scale-up-rules

            state

show maestro configuration

      hft state

      orchestrator-amount

      orchestrator-member-id

      orchestrator-site-amount

      orchestrator-site-id

      orchestrators base-vlan

      security-appliances inter-site

            base-vlan

            vlan encapsulation

            vlan translation

      uplink-trunk-mode state

      vxlan state

show maestro gateway serial <Serial Number> description

show maestro lsp

      configuration {all | group <1-1024>}

      history <1-1000>

      status

show maestro port <Name>

      admin-state

      admin-state

      auto-negotiation

      mtu

      optic-info

      optic-info-details

      qsfp-mode

      type

      vlans

show maestro security-group id <ID>

      description

      interface <Name> description

      shared-uplinks state

      site-id <ID>

            description

            member <ID> description

show maestro security-group verify-new-config

show maestro snmp traps port-state

Commands

Command

Description

show maestro auto-scale

Shows the Auto-Scaling settings.

See Maestro Auto-Scaling.

  • interactive-rules

    Shows the status of the Auto-Scaling rules in realtime.

  • interactive-status

    Shows the status of the Auto-Scaling in Security Groups in realtime.

  • scale-units

    Shows the configured scale units.

  • scale-down-rules

    Shows the Scale-Down policy.

  • scale-up-rules

    Shows the Scale-Up policy.

  • state

    Shows the Auto-Scaling state.

show maestro configuration

Shows the Orchestrator settings.

  • hft state

    Show high frequency trading configuration.

  • orchestrator-amount

    Shows the number of configured Orchestrators in this Maestro deployment.

  • orchestrator-member-id

    Shows the configured Orchestrator Member ID on its Site.

  • orchestrator-site-amount

    Shows the number of configured Sites in this Maestro deployment.

  • orchestrator-site-id

    Shows the configured Orchestrator Site ID.

  • orchestrators base-vlan

    Shows the Orchestrator's base VLAN ID.

  • security-appliances inter-site base-vlan

    Shows the base VLAN ID for the Security Appliance communication between Sites.

  • security-appliances inter-site vlan encapsulation

    Shows the state of the Site-Sync VLAN encapsulation for the Security Appliances.

  • security-appliances inter-site vlan translation

    Shows the Site-Sync VLAN translation configuration for the Security Appliances.

  • uplink-trunk-mode state

    Shows the state of the Uplink Trunk Mode.

  • vxlan state

    Shows the state of VXLAN.

show maestro gateway serial <Serial Number> description

Shows the configured description for the selected Security Appliance.

Press the TAB key to see the detected Serial Numbers.

show maestro lsp

Shows the Link State Propagation (LSP) settings.

See Configuring Link State Propagation (LSP) on a Maestro Orchestrator.

show maestro port <Name>

Shows the settings for the specified port.

Press the TAB key to select the required port.

  • admin-state

    Shows the port administrative state.

  • auto-negotiation

    Shows the port auto-negotiation state.

  • mtu

    Shows the port MTU.

  • optic-info

    Shows information about the QSFP transceiver inserted in the port.

  • optic-info-details

    Shows detailed information about the QSFP transceiver inserted in the port.

  • qsfp-mode

    Shows the port QSFP mode (port speed).

  • type

    Shows the port type - Management, Uplink, Downlink, Internal Sync (site_sync), External Sync (ssm_sync).

  • vlans

    Deprecated command

Related commands:

show maestro security-group id <ID>

Shows

  • description

    Shows the configured description for this Security Group.

  • interface <Name of Interface> description

    Shows the configured description for the interface.

  • shared-uplinks state

    Shows the Shared Uplinks configuration.

    See Shared Uplink Ports on a Maestro Security Group.

  • site-id <ID> description

    Shows the configured description for the Site.

  • site-id <ID> member <ID> description

    Shows the configured description for the Orchestrator on the Site.

show maestro security-group verify-new-config

Verifies the new configuration for Security Groups that was not applied yet.

show maestro snmp traps port-state

Shows the state of the SNMP traps for Orchestrator ports.