cplink

This command is supported only on:

  • Maestro Orchestrator

Note - You must run this command in the Expert mode.

Description

Shows advanced information about the ports on the Maestro Orchestrator.

See sk180812.

Related Commands

Syntax

cplink -h

cplink [-j] [-r] <Port>

Parameters

Parameter

Description

-h

Shows the built-in help.

-j

--json

Shows the output in the JSON format.

-r

--raw

Shows the additional details.

Output may not contain values for all these parameters.

  • Group Opcode

  • Status Opcode

  • Attenuation

  • Bias Current

  • CDR RX

  • CDR TX

  • Compliance

  • FW Version

  • LOS Alarm

  • Power Class

  • Rx Power Current

  • Temperature

  • Tx Power Current

  • Voltage

  • Wavelength

<Port>

Specifies the port to inspect.

One of these:

  • A physical port:

    <Port Number>

    Example: cplink 1

  • A port label:

    <Orchestrator ID>/<Port Label>

    Example: cplink 1/1

  • A port label with subport:

    <Orchestrator ID>/<Port Label>/<Port Split ID>

    Example: cplink 1/1/1

If the port is not split with a break-out cable, then enter the Port Number as it appears on the Orchestrator's front panel.

If a break-out cable is connected to a port, then enter the applicable numbers:

  • For Split 1, enter <Port Label>

  • For Split 2, enter <Port Label>/2

  • For Split 3, enter <Port Label>/3

  • For Split 4, enter <Port Label>/4

Examples

[Expert@MHO1_1:0]# orch_stat -p

Ports Status
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
| Physical Port | Interface Name | Type      | SG  | QSFP Mode | Admin State | Link State | Transceiver State | Operating Speed | MTU   | RX Frames | TX Frames |
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
| 1/1/1         | eth1-Mgmt1     | Mgmt      | 1   | 10G       | UP          | UP         | PLUGGED           | 10GB_CR         | 10240 | 155831054 | 104498732 |
|               |                |           | 2   |           |             |            |                   |                 |       |           |           |
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
...
[Expert@MHO1_1:0]#

[Expert@MHO1_1:0]# cplink 1/1/1

Troubleshooting Info
====================
Recommendation:                 No issue was observed

Module Info
===========
Cable Technology:               Passive
Cable Type:                     Passive copper cable
Digital Diagnostic Monitoring:  No
Identifier:                     SFP28/SFP+
OUI:                            Other
Rev:                            A0
Transfer Distance [m]:          1
Vendor Name:                    Gigalight
Vendor Part Number:             GPP-PC192-3001CP
Vendor Serial Number:           GE18190037

Operational Info
================
Auto Negotiation:               ON
FEC:                            No FEC
Loopback Mode:                  No Loopback
Physical state:                 LinkUp
Speed:                          10GbE
State:                          Active
Width:                          1x

Supported Info
==============
Enabled Link Speed:             10G
Supported Cable Speed:          10G, 1G

EYE Opening Info
================
Height Eye Opening [mV]:        246
Phase  Eye Opening [psec]:      0
Physical Grade:                 18149

Tool Information
================
Firmware Version:               13.2012.2140
MFT Version:                    mft 4.26.1-3
[Expert@MHO1_1:0]#
 
[Expert@MHO1_1:0]# orch_stat -p

Ports Status
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
| Physical Port | Interface Name | Type      | SG  | QSFP Mode | Admin State | Link State | Transceiver State | Operating Speed | MTU   | RX Frames | TX Frames |
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
| 1/1/1         | eth1-Mgmt1     | Mgmt      | 1   | 10G       | UP          | UP         | PLUGGED           | 10GB_CR         | 10240 | 155831054 | 104498732 |
|               |                |           | 2   |           |             |            |                   |                 |       |           |           |
+---------------+----------------+-----------+-----+-----------+-------------+------------+-------------------+-----------------+-------+-----------+-----------+
...
[Expert@MHO1_1:0]#

[Expert@MHO1_1:0]# cplink 1/1/1 -r

Troubleshooting Info
====================
Group Opcode:                   N/A
Recommendation:                 No issue was observed
Status Opcode:                  0

Module Info
===========
Attenuation (5g,7g,12g) [dB]:   N/A
Bias Current [mA]:              N/A
CDR RX:                         values: ['N/A']
CDR TX:                         values: ['N/A']
Cable Technology:               Passive
Cable Type:                     Passive copper cable
Compliance:                     N/A
Digital Diagnostic Monitoring:  No
FW Version:                     N/A
Identifier:                     SFP28/SFP+
LOS Alarm:                      N/A
OUI:                            Other
Power Class:                    N/A
Rev:                            A0
Rx Power Current [dBm]:         N/A
Temperature [C]:                N/A
Transfer Distance [m]:          1
Tx Power Current [dBm]:         N/A
Vendor Name:                    Gigalight
Vendor Part Number:             GPP-PC192-3001CP
Vendor Serial Number:           GE18190037
Voltage [mV]:                   N/A
Wavelength [nm]:                N/A

Operational Info
================
Auto Negotiation:               ON
FEC:                            No FEC
Loopback Mode:                  No Loopback
Physical state:                 LinkUp
Speed:                          10GbE
State:                          Active
Width:                          1x

Supported Info
==============
Enabled Link Speed:             mask: 0x00007010, values: ['10G']
Supported Cable Speed:          mask: 0x00001001, values: ['10G', '1G']

EYE Opening Info
================
Height Eye Opening [mV]:        values: ['246']
Phase  Eye Opening [psec]:      values: ['0']
Physical Grade:                 values: ['18149']

Tool Information
================
Firmware Version:               13.2012.2140
MFT Version:                    mft 4.26.1-3
[Expert@MHO1_1:0]#