Monitoring Falcon Acceleration Cards in Gaia Clish

In This Section:

Viewing the Network Interface Type

Step

Description

Connect to the command line on the Security Appliance.

Examine the interface type:

show interface <Interface Name> type

For the accelerated interface, the output shows AC Ethernet.
For the accelerated interface in the Acceleration Bypass mode, the output shows AC Bypassed.

Example 1 - Accelerated interface:

MyAppliance> show interface eth1-01 type
type AC Ethernet
MyAppliance>

Example 2 - Non-accelerated interface:

MyAppliance> show interface eth2-01 type
type AC Bypassed
MyAppliance>

Example 3 - Regular interface:

MyAppliance> show interface eth3-01 type
type ethernet
MyAppliance>

Viewing the Hardware Information on the Appliance

Step	Description
1	Connect to the command line on the Security Appliance.
2	Log in to Gaia Clish.
3	To show the hardware information about the acceleration cards only, run: `show asset ac`
4	To show all hardware information, including the acceleration cards, run: `show asset all`

Notes:

For the accelerated interface, the output shows Mode: Accelerated.
For the accelerated interface in the Acceleration Bypass mode, the output shows Mode: AC Bypassed.

Example 1 - Hardware information about the acceleration cards:

MyAppliance> show asset ac
AC Slot 1 Description: CPAC-falcon-10G-B
AC Slot 1 Serial Number: XXXXXXXXXXXXX
AC Slot 1 Memory: 8.00 GB
AC Slot 1 Chip Version: XLP5XX Rev A1
AC Slot 1 Part Number: XXXXXXXXXXXXXXX-XX
AC Slot 1 Hardware Revision: 03.20
AC Slot 1 EEPROM Revision: 1.3
AC Slot 1 CPLD Version: 9
AC Slot 1 Mode: Accelerated
AC Slot 3 Description: CPAC-falcon-10G-B
AC Slot 3 Serial Number: XXXXXXXXXXXXX
AC Slot 3 Memory: 8.00 GB
AC Slot 3 Chip Version: XLP5XX Rev A1
AC Slot 3 Part Number: XXXXXXXXXXXXXXX-XX
AC Slot 3 Hardware Revision: 03.20
AC Slot 3 EEPROM Revision: 1.3
AC Slot 3 CPLD Version: 9
AC Slot 3 Mode: Accelerated
MyAppliance>

Example 2 - All hardware information:

MyAppliance> show asset all
Platform: PH-20-00
Model: Check Point 15400
Serial Number: XXXXXXXXXXXXXX
CPU Model: Intel(R) Xeon(R) CPU E5-2630 v3
CPU Frequency: 2400.121
Number of Cores: 16
CPU Hyperthreading: Enabled
Number of disks: 2
Disk 1 Model: ST1000NM0033-9ZM173
Disk 1 Capacity: 1.00 TB
Disk 2 Model: ST1000NM0033-9ZM173
Disk 2 Capacity: 1.00 TB
Total Disks size: 2000 GB
Total Memory: 32768
Memory Slot 1 Size: 8192
Memory Slot 2 Size: 8192
Memory Slot 3 Size: 8192
Memory Slot 4 Size: 8192
Power supply 1 name: Power Supply #1
Power supply 1 status: Up
Power supply 2 name: Power Supply #2
Power supply 2 status: Down
LOM Status: Installed
LOM Firmware Revision: 3.14
Number of line cards: 2
Line card 1 type: 4 ports 10GbE Fiber Acceleration Card
Line card 2 type: 4 ports 10GbE Fiber Acceleration Card
AC Slot 1 Description: CPAC-falcon-10G-B
AC Slot 1 Serial Number: XXXXXXXXXXXXX
AC Slot 1 Memory: 8.00 GB
AC Slot 1 Chip Version: XLP5XX Rev A1
AC Slot 1 Part Number: XXXXXXXXXXXXXXX-XX
AC Slot 1 Hardware Revision: 03.20
AC Slot 1 EEPROM Revision: 1.3
AC Slot 1 CPLD Version: 9
AC Slot 1 Mode: Accelerated
AC Slot 3 Description: CPAC-falcon-10G-B
AC Slot 3 Serial Number: XXXXXXXXXXXXX
AC Slot 3 Memory: 8.00 GB
AC Slot 3 Chip Version: XLP5XX Rev A1
AC Slot 3 Part Number: XXXXXXXXXXXXXXX-XX
AC Slot 3 Hardware Revision: 03.20
AC Slot 3 EEPROM Revision: 1.3
AC Slot 3 CPLD Version: 9
AC Slot 3 Mode: Accelerated
MyAppliance>

Viewing the Hardware Sensors on the Installed Cards

Step

Description

Connect to the command line on the Security Appliance.

Run one of these two commands to show the information from the hardware sensors:

show sysenv all
cpstat -f sensors os

For the Falcon Acceleration Cards, the output shows the data from these sensors:

Temperature of acceleration card slots (examine the Falcon-<Slot#> <Speed> NPU Temp).
Fan on acceleration card (examine the Falcon-<Slot#> <Speed> Fan).
Voltage on acceleration card (examine the Falcon-<Slot#> <Speed> Vcore).

Example 1

MyAppliance> show sysenv all
Hardware Information

Name Value Unit Type Status Maximum Minimum
CPU0 Vcore 1.81 Volt Voltage 0 1.91 1.41
CPU1 Vcore 1.82 Volt Voltage 0 1.91 1.41
CPU0 DDR4-1 1.19 Volt Voltage 0 1.28 1.12
CPU0 DDR4-2 1.19 Volt Voltage 0 1.28 1.12
CPU1 DDR4-1 1.19 Volt Voltage 0 1.28 1.12
CPU1 DDR4-2 1.19 Volt Voltage 0 1.28 1.12
VCC 12V 12.05 Volt Voltage 0 12.77 11.14
VCC 3V 3.31 Volt Voltage 0 3.53 3.07
VCC 5V 5.04 Volt Voltage 0 5.35 4.66
3VSB 3.31 Volt Voltage 0 3.53 3.07
5VSB 5.08 Volt Voltage 0 5.35 4.66
VBAT 3.23 Volt Voltage 0 3.53 1.85
Falcon-1 10G NPU Vcore 0.98 Volt Voltage 0 1.04 0.59
CPU0 Temp 40.00 Celsius Temperature 0 81 0
CPU1 Temp 44.63 Celsius Temperature 0 81 0
Intake Temp 25.75 Celsius Temperature 0 70 0
Outlet Temp 32.00 Celsius Temperature 0 70 0
Falcon-1 10G NPU Temp 52.50 Celsius Temperature 0 88 5
System Fan 1 9183.00 RPM Fan 0 20806 2369
System Fan 2 9121.00 RPM Fan 0 20806 2369
System Fan 3 9000.00 RPM Fan 0 20806 2369
System Fan 4 9000.00 RPM Fan 0 20806 2369
Falcon-1 10G Fan 8385.00 RPM Fan 0 9600 6400
Power Supply #1 Up Up/Down Power 0 Up Down
Power Supply #2 Down Up/Down Power 1 Up Down
BIOS Valid Valid/Invalid BIOS 0 Valid Invalid
MyAppliance>

Example 2

MyAppliance> cpstat -f sensors os

Temperature Sensors
--------------------------------------------------------
|Name |Value|Unit |Type |Status|
--------------------------------------------------------
|CPU0 Temp |36.75|Celsius|Temperature| 0|
|Intake Temp |26.75|Celsius|Temperature| 0|
|Outlet Temp |16.25|Celsius|Temperature| 0|
|Falcon-1 10G NPU Temp|49.00|Celsius|Temperature| 0|
|Falcon-3 10G NPU Temp|46.00|Celsius|Temperature| 0|
--------------------------------------------------------

Fan Speed Sensors
-------------------------------------------
|Name |Value |Unit|Type|Status|
-------------------------------------------
|System Fan 1 |9060.00|RPM |Fan | 0|
|System Fan 2 |9121.00|RPM |Fan | 0|
|System Fan 3 |9060.00|RPM |Fan | 0|
|System Fan 4 |9183.00|RPM |Fan | 0|
|Falcon-1 10G Fan|8490.00|RPM |Fan | 0|
|Falcon-3 10G Fan|8437.00|RPM |Fan | 0|
-------------------------------------------

Voltage Sensors
--------------------------------------------------
|Name |Value|Unit|Type |Status|
--------------------------------------------------
|CPU0 Vcore |1.81 |Volt|Voltage| 0|
|CPU0 DDR4-1 |1.19 |Volt|Voltage| 0|
|CPU0 DDR4-2 |1.19 |Volt|Voltage| 0|
|VCC 12V |12.14|Volt|Voltage| 0|
|VCC 3V |3.29 |Volt|Voltage| 0|
|VCC 5V |5.05 |Volt|Voltage| 0|
|3VSB |3.28 |Volt|Voltage| 0|
|5VSB |5.00 |Volt|Voltage| 0|
|VBAT |3.19 |Volt|Voltage| 0|
|Falcon-1 10G NPU Vcore|0.98 |Volt|Voltage| 0|
|Falcon-3 10G NPU Vcore|0.98 |Volt|Voltage| 0|
--------------------------------------------------

MyAppliance>