set snmp traps trap-name
In the R81.10.X releases, this command is available starting from the R81.10.00 version.
Description
Configures an SNMP trap.
See show snmp traps enabled-traps.
Syntax
|
|
Parameters
|
Parameter |
Description |
|---|---|
|
enable |
Enables or disables this SNMP trap. |
|
repetitions |
Configures the number of repetitions for sending the SNMP trap during the event. |
|
repetitions-delay |
Configures the time (in seconds) between sending each SNMP trap during the event. |
|
severity |
Configures the severity for the SNMP trap. |
|
threshold |
Configures the threshold value, above / below which to start sending the SNMP trap. |
|
trap-name |
Specifies the SNMP trap. |
Supported SNMP Traps
|
Trap Name in Gaia Clish |
Monitored Object |
Description |
Default Trap State |
Threshold Operand |
Threshold Default Value |
Threshold Valid Values |
Trap Default Severity |
Trap Default Repetitions |
Default Repetition Delay |
Trap SNMP OID |
|---|---|---|---|---|---|---|---|---|---|---|
|
|
Interface disconnected |
Either network cable was disconnected, ICMP monitor failed to reach a monitored server, or LAN interface was manually disabled |
Enabled |
N / A |
N / A |
N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.1 |
|
|
VLAN removed |
VLAN was removed from a physical interface |
Enabled |
N / A |
N / A |
N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.2 |
|
|
High connection rate |
New connection rate is above the configured threshold value (connections / second) |
Enabled |
eq_gt |
3000 |
1 - 10000 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.3 |
|
|
High concurrent connections |
The number of concurrent connections is above the configured threshold value |
Enabled |
eq_gt |
50000 |
0 - 300000 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.4 |
|
|
Free disk space |
Free spaces on a disk partition free space is below the configured threshold value (%) |
Enabled |
eq_lt |
10 |
0 - 100 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.2.1 |
|
|
CPU utilization |
CPU usage is above the configured threshold value (%) |
Disabled |
eq_gt |
95 |
0 - 100 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.3.1 |
|
|
High CPU interrupts rate |
Accepted packet rate is above the configured threshold value (interrupts / seconds) |
Disabled |
eq_gt |
20000000 |
0 - 2147483640 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.3.2 |
|
|
Memory utilization |
Memory utilization is above the configured threshold value (%) |
Enabled |
gt |
90 |
0 - 100 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.4.2 |
|
|
High Firewall throughput |
Firewall throughput is above the configured threshold value (megabytes / second) |
Enabled |
eq_gt |
1000 |
0 - 3000 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.5 |
|
|
High accepted packet rate |
Accepted packet rate is above the configured threshold value (packets / second) |
Enabled |
eq_gt |
100000 |
0 - 300000 |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.1.6 |
|
|
Cluster member state changed |
Cluster member state changed (the cluster member identifier is provided in the trap) |
Disabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.6.1 |
|
|
Cluster member severe problem |
Cluster member suffers from a severe problem that prevents it from handling traffic (even when the other cluster member is down) |
Disabled | N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.6.2 |
|
|
Cluster member state |
Cluster member is either in the "Active Attention" state, or in the Blocking state (the cluster member identifier is provided in the trap) |
Disabled | N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.6.3 |
|
|
Cluster device status |
One of the Critical Devices on the cluster member (for example, "Synchronization") reported its state as "problem" |
Disabled | N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.6.4 |
|
|
Cluster interface problem |
Cluster member detected a problem with one of the cluster interfaces (the interface name is provided in the trap) |
Disabled | N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.6.5 |
|
|
Connection with log server error |
Unable to send logs to the configured Log Server |
Enabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.7.2 |
|
|
VPN tunnels are down |
VPN tunnels are down (names of VPN peer are provided in the trap) |
Disabled |
N / A | N / A | N / A |
4 |
0 |
300 |
1.3.6.1.4.1.2620.1.2000.8.1 |
|
|
Temperature Sensor Status |
Temperature is above the threshold required by vendor |
Enabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.5.1.1 |
|
|
Fan Speed Status |
Fan speed is above or below the threshold required by vendor |
Enabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.5.2.1 |
|
|
Voltage Sensor Status |
Voltage is above or below the threshold required by vendor |
Enabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.5.3.1 |
|
|
Power Supply Status |
Power supply status changed |
Enabled |
N / A | N / A | N / A |
4 |
1 |
30 |
1.3.6.1.4.1.2620.1.2000.5.4.1 |
Example Command
|
|