ClusterXL Monitoring Commands

Description

Use the monitoring commands to make sure that the cluster and the Cluster Members work properly, and to define Critical Devices. A Critical Device (also known as a Problem Notification, or pnote) is a special software device on each Cluster Member, through which the critical aspects for cluster operation are monitored. When the critical monitored component on a Cluster Member fails to report its state on time, or when its state is reported as problematic, the state of that member is immediately changed to 'Down'.

Syntax

Notes:

In Gaia Clish:

Enter the show cluster<ESC><ESC> to see all the available commands.
In Expert mode:

Run the cphaprob command see all the available commands.

You can run the cphaprob commands from Gaia Clish as well.
Syntax legend:
1. Curly brackets or braces { }:
  
  Enclose a list of available commands or parameters, separated by the vertical bar |, from which user can enter only one.
2. Angle brackets < >:
  
  Enclose a variable - a supported value user needs to specify explicitly.
3. Square brackets or brackets [ ]:
  
  Enclose an optional command or parameter, which user can also enter.
You can include these commands in scripts to run them automatically.

The meaning of each command is explained in the next sections.

Table: ClusterXL Monitoring Commands
Description of Command	Command in Gaia Clish	Command in Expert Mode
Show states of Cluster Members and their names (see Viewing Cluster State)	`show cluster state`	`cphaprob [-vs <VSID>] state`
Show Critical Devices (Pnotes) and their states on the Cluster Member (see Viewing Critical Devices)	`show cluster members pnotes {all \| problem}`	`cphaprob [-l] [-ia] [-e] list`
Show cluster interfaces on the cluster member (see Viewing Cluster Interfaces)	`show cluster members interfaces {all \| secured \| virtual \| vlans}`	`cphaprob [-vs all] [-a] [-m] if`
Show cluster bond configuration on the Cluster Member (see Viewing Bond Interfaces)	`show cluster bond {all \| name <bond_name>}`	`cphaprob show_bond [<bond_name>]`
Show groups of bonds on the Cluster Member (see Viewing Bond Interfaces)	`N / A`	`cphaprob show_bond_groups`
Show (and reset) cluster failover statistics on the Cluster Member (see Viewing Cluster Failover Statistics)	`show cluster failover [reset {count \| history}]`	`cphaprob [-reset {-c \| -h}] [-l <count>] show_failover`
Show information about the software version (including hotfixes) on the local Cluster Member and its matches/mismatches with other Cluster Members (see Viewing Software Versions on Cluster Members)	`show cluster release`	`cphaprob release`
Show Delta Sync statistics on the Cluster Member (see Viewing Delta Synchronization)	`show cluster statistics sync [reset]`	`cphaprob [-reset] syncstat`
Show Delta Sync statistics for the Connections table on the Cluster Member (see Viewing Cluster Delta Sync Statistics for Connections Table)	`show cluster statistics transport [reset]`	`cphaprob [-reset] ldstat`
Show the Cluster Control Protocol (CCP) mode on the Cluster Member (see Viewing Cluster Interfaces)	`show cluster members interfaces virtual`	`cphaprob [-vs all] -a if`
Show the IGMP membership of the Cluster Member (see Viewing IGMP Status)	`show cluster members igmp`	`cphaprob igmp`
Show cluster unique IP's table on the Cluster Member (see Viewing Cluster IP Addresses)	`show cluster members ips` `show cluster members monitored`	`cphaprob tablestat` `cphaprob -m tablestat`
Show the Cluster Member ID Mode in local logs - by Member ID (default) or Member Name (see Viewing the Cluster Member ID Mode in Local Logs)	`show cluster members idmode`	`cphaprob names`
Show interfaces, which the RouteD monitors on the Cluster Member when you configure OSPF (see Viewing Interfaces Monitored by RouteD)	`show ospf interfaces [detailed]`	`cphaprob routedifcs`
Show roles of RouteD daemon on Cluster Members (see Viewing Roles of RouteD Daemon on Cluster Members)	`show cluster roles`	`cphaprob roles`
Show Cluster Correction Statistics (see Viewing Cluster Correction Statistics)	`N / A`	`cphaprob [{-d \| -f \| -s}] corr`
Show the Cluster Control Protocol (CCP) mode (see Viewing the Cluster Control Protocol (CCP) Settings)	`show cluster members interfaces virtual`	`cphaprob -a if`
Show the Cluster Control Protocol (CCP) Encryption settings (see Viewing the Cluster Control Protocol (CCP) Settings)	`show cluster members ccpenc`	`cphaprob ccp_encrypt`
Shows the state of the Multi-Version Cluster (see Viewing the State of the Multi-Version Cluster Mechanism)	`show cluster members mvc`	`N / A`
Show Full Connectivity Upgrade statistics (see Viewing Full Connectivity Upgrade Statistics)	`N / A`	`cphaprob fcustat`

List of the Gaia Clish show cluster commands

show cluster

bond

all

name <Name of Bond>

failover

members

ccpenc

idmode

igmp

interfaces

all

secured

virtual

vlans

ips

monitored

mvc

pnotes

all

problem

release

roles

state

statistics

sync [reset]

transport [reset]

List of the cphaprob commands

Note - Some commands are not applicable to 3rd party clusters.

cphaprob [-vs <VSID>] state

cphaprob [-reset {-c | -h}] [-l <count>] show_failover

cphaprob names

cphaprob [-reset] [-a] syncstat

cphaprob [-reset] ldstat

cphaprob [-l] [-i[a]] [-e] list

cphaprob [-vs all] [-a] [-m] if

cphaprob latency

cphaprob show_bond [<bond_name>]

cphaprob show_bond_groups

cphaprob igmp

cphaprob fcustat

cphaprob [-m] tablestat

cphaprob routedifcs

cphaprob roles

cphaprob release

cphaprob ccp_encrypt

cphaprob [{-d | -f | -s}] corr