Tunnel Management

In This Section: Overview of Tunnel Management Permanent Tunnels VPN Tunnel Sharing Configuring Tunnel Features

Overview of Tunnel Management

The VPN tunnel transports data securely. You can manage the types of tunnels and the number of tunnels with these features:

• Permanent Tunnels - Keeps VPN tunnels active to allow real-time monitoring capabilities.
• VPN Tunnel Sharing - Provides greater interoperability and scalability between Security Gateways. It also controls the number of VPN tunnels created between peer Security Gateways.

See the status of all VPN tunnels in SmartView Monitor. For details see Monitoring Tunnels in the R80.30 Logging and Monitoring Administration Guide.

Permanent Tunnels

As companies have become more dependent on VPNs for communication to other sites, uninterrupted connectivity has become more crucial than ever before. Therefore it is essential to make sure that the VPN tunnels are kept up and running. Permanent Tunnels are constantly kept active and as a result, make it easier to recognize malfunctions and connectivity problems. Administrators can monitor the two sides of a VPN tunnel and identify problems without delay.

Each VPN tunnel in the community may be set to be a Permanent Tunnel. Since Permanent Tunnels are constantly monitored, if the VPN tunnel is down, then a log, alert, or user defined action, can be issued. A VPN tunnel is monitored by periodically sending "tunnel test" packets. As long as responses to the packets are received the VPN tunnel is considered "up." If no response is received within a given time period, the VPN tunnel is considered "down." Permanent Tunnels can only be established between Check Point Security Gateways. The configuration of Permanent Tunnels takes place on the community level and:

• Can be specified for an entire community. This option sets every VPN tunnel in the community as permanent.
• Can be specified for a specific Security Gateway. Use this option to configure specific Security Gateways to have permanent tunnels.
• Can be specified for a single VPN tunnel. This feature allows configuring specific tunnels between specific Security Gateways as permanent.

Permanent Tunnels in a MEP Environment

In a Multiple Entry Point (MEP) environment, VPN tunnels that are active are rerouted from the predefined primary Security Gateway to the backup Security Gateway if the primary Security Gateway becomes unavailable. When a Permanent Tunnel is configured between Security Gateways in a MEP environment where RIM is enabled, the satellite Security Gateways see the center Security Gateways as "unified." As a result, the connection will not fail but will fail over to another center Security Gateway on a newly created permanent tunnel. For more information on MEP see Multiple Entry Point VPNs.

Tunnel Testing for Permanent Tunnels

Check Point uses a proprietary protocol to test if VPN tunnels are active, and supports any site-to-site VPN configuration. Tunnel testing requires two Security Gateways, and uses UDP port 18234. Check Point tunnel testing protocol does not support 3rd party Security Gateways.

Terminating Permanent Tunnels

Once a Permanent Tunnel is no longer required, the tunnel can be shut down. Permanent Tunnels are shut down by deselecting the configuration options to make them active and re-installing the policy.

Dead Peer Detection

In addition to Tunnel Testing, Dead Peer Detection (DPD) is a different method to test if VPN tunnels are active. Dead Peer Detection does support 3rd party Security Gateways and supports permanent tunnels with interoperable devices based on IKEv1/IKEv2 DPD (IKEv1 DPD is based on RFC 3706). It uses IPsec traffic patterns to minimize the number of messages required to confirm the availability of a peer.

The tunnel testing mechanism is the recommended keepalive mechanism for Check Point to Check Point VPN gateways because it is based on IPsec traffic and requires an IPsec established tunnel. DPD is based on IKE encryption keys only.

DPD has two modes:

• DPD responder mode - Requires an R77.10 or higher gateway managed by an R77 or higher management server.
• Permanent tunnel mode based on DPD - Requires an R77.10 or higher gateway managed by an R77.10 or higher management.

DPD Responder Mode

In this mode the Check Point gateway sends the IKEv1 DPD Vendor ID to peers, from which the DPD Vendor ID was received.

To enable DPD Responder Mode:

1. On each Security Gateway, run this command:

   ckp_regedit -a SOFTWARE/CheckPoint/VPN1 forceSendDPDPayload -n 1

2. To prevent a problem, where the Check Point Security Gateway deletes IKE SAs:

   Note - The DPD mechanism is based on IKE SA keys. In some situations, the Check Point Security Gateway deletes IKE SAs, and a VPN peer, usually a 3rd Party gateway, sends DPD requests and does not receive a response. As a result, the VPN peer concludes that the Check Point Security Gateway is down. The VPN peer can then delete the IKE and IPsec keys, which causes encrypted traffic from the Check Point Security Gateway to be dropped by the remote peer.

   1. In SmartConsole, click Menu > Global properties > Advanced > Configure.
   2. Click VPN Advanced Properties > VPN IKE properties.
   3. Select keep_IKE_SAs.
   4. Click OK.
   5. Install the Access Control Policy.

To disable DPD Responder Mode:

On each Security Gateway, run this command:

ckp_regedit -d SOFTWARE/CheckPoint/VPN1 forceSendDPDPayload

Permanent Tunnel Mode Based on DPD

DPD can monitor remote peers with the permanent tunnel feature. All related behavior and configurations of permanent tunnels are supported.

To configure DPD for a permanent tunnel, the permanent tunnel must be in the VPN community. After you configure the permanent tunnel, configure Permanent Tunnel mode Based on DPD. There are different possibilities for permanent tunnel mode:

• tunnel_test (default) - The permanent tunnel is monitored by tunnel test (as in earlier versions). It works between Check Point gateways only. Keepalive packets are always sent.
• dpd - The active DPD mode. A peer receives DPD requests at regular intervals (10 seconds). DPD requests are only sent when there is no traffic from the peer.
• passive - The passive DPD mode. Peers do not send DPD requests to this peer. Tunnels with passive peers are monitored only if there is IPsec traffic and incoming DPD requests.

  Note: To use this mode for only some gateways, enable the forceSendDPDPayload registry key on Check Point remote peers.

To enable DPD monitoring:

On each VPN gateway in the VPN community, configure the tunnel_keepalive_method property, in GuiDBedit Tool (see sk13009) or dbedit (see skI3301). This includes 3rd Party gateways. (You cannot configure different monitor mechanisms for the same gateway).

1. In GuiDBedit Tool, go to Network Objects > network_objects > <gateway> > VPN.
2. For the Value, select a permanent tunnel mode.
3. Save all the changes.
4. Install the Access Control Policy.

Optional Configuration

• IKE Initiation Prevention - By default, when a valid IKE SA is not available, a DPD request message triggers a new IKE negotiation. To prevent this behavior, set the property dpd_allowed_to_init_ike to false.

  Edit the property in GuiDBedit Tool (see sk13009) > Network Objects > network_objects > <gateway Name> > VPN.

• Delete IKE SAs for dead peer - Based on RFC 3706, a VPN gateway has to delete IKE SAs from a dead peer. This functionality is enabled, by default.

  To disable this feature, set the DPD_DONT_DEL_SA environment variable to 0:

  • To do this temporarily, run:

    cpstop

    export DPD_DONT_DEL_SA=0

    cpstart

  • To do this permanently:

    Add this line to the $CPDIR/tmp/.CPprofile.sh file and then reboot:

    DPD_DONT_DEL_SA=0 ; export DPD_DONT_DEL_SA

  To re-enable the feature:

  • Temporarily:

    cpstop

    export DPD_DONT_DEL_SA=0

    cpstart

  • Permanently:

    Remove the DPD_DONT_DEL_SA line from the $CPDIR/tmp/.CPprofile.sh file and then reboot.

VPN Tunnel Sharing

For a VPN community, the VPN tunnel sharing configuration is set on the Tunnel Management page of the Community Properties window.

For a specific Security Gateway, the configuration is set on the VPN Advanced page of the Security Gateway properties window.

VPN Tunnel Sharing provides greater interoperability and scalability by controlling the number of VPN tunnels created between peer Security Gateways. Configuration of VPN Tunnel Sharing can be set on both the VPN community and Security Gateway object.

• One VPN Tunnel per each pair of hosts - A VPN tunnel is created for every session initiated between every pair of hosts.
• One VPN Tunnel per subnet pair- Once a VPN tunnel has been opened between two subnets, subsequent sessions between the same subnets will share the same VPN tunnel. This is the default setting and is compliant with the IPsec industry standard.
• One VPN Tunnel per Security Gateway pair - One VPN tunnel is created between peer Security Gateways and shared by all hosts behind each peer Security Gateway.

In case of a conflict between the tunnel properties of a VPN community and a Security Gateway object that is a member of that same community, the "stricter" setting is followed. For example, a Security Gateway that was set to One VPN Tunnel per each pair of hosts and a community that was set to One VPN Tunnel per subnet pair, would follow One VPN Tunnel per each pair of hosts.

Tunnel test is a proprietary Check Point protocol used to see if VPN tunnels are active. Tunnel testing requires two Security Gateways and uses UDP port 18234. Third party gateways do not support tunnel testing.

Configuring Tunnel Features

To configure Tunnel Management options:

1. In SmartConsole, click Object Explorer (Ctrl+E)
2. Click New > VPN Community and choose Star Community or Meshed community.
3. Click Tunnel Management. and configure the tunnel settings:
   • Permanent Tunnels
   • Tracking Options
   • VPN Tunnel Sharing

Permanent Tunnels

In the Star Community or Meshed community object, on the Tunnel Management page, select Set Permanent Tunnels.

These are the options:

• On all tunnels in the community
• On all tunnels of specific Security Gateways
• On specific tunnels in the community

To configure all tunnels as permanent, select On all tunnels in the community. Clear this option to terminate all Permanent Tunnels in the community.

To configure on all tunnels of specific Security Gateways:

1. Select On all tunnels of specific gateways and click Select Gateways.

   The Select Gateway window opens.

   To terminate Permanent Tunnels connected to a specific Security Gateway, select the Security Gateway object and click Remove.

2. To configure the Tracking options for a specific Security Gateway, select a Security Gateway object and click Gateway Tunnel Properties.

To configure on specific tunnels in the community:

1. Select On specific tunnels in the community and click Select Permanent Tunnels.

   The Select Permanent Tunnels window opens.

2. Double click in the white cell that intersects the Security Gateways where a permanent tunnel is required.

   The Tunnel Properties window opens.

3. Click Set these tunnels to be permanent tunnels.

   To terminate the Permanent Tunnel between these two Security Gateways, clear Set these tunnels to be permanent tunnels.

4. Click OK.

Advanced Permanent Tunnel Configuration

In SmartConsole:

1. Click Menu > Global properties.
2. Click Advanced > Configure.
3. Click VPN Advanced Properties > Tunnel Management to see the five attributes that may be configured to customize the amount of tunnel tests sent and the intervals in which they are sent:
   • life_sign_timeout - Set the amount of time the tunnel test or DPD runs without a response before the peer host is declared 'down.'
   • life_sign_transmitter_interval - Set the time between tunnel tests or DPD.
   • life_sign_retransmissions_count - When a tunnel test does not receive a reply, another test is resent to confirm that the peer is 'down.' The Life Sign Retransmission Count is set to how many times the tunnel test is resent without receiving a response.
   • life_sign_retransmissions_interval - Set the time between the tunnel tests that are resent after it does not receive a response from the peer.
   • cluster_status_polling_interval - (applicable for High Availability Clusters only) - Set the time between tunnel tests between a primary Security Gateway and a backup Security Gateway. The tunnel test is sent by the backup Security Gateway. When there is no reply, the backup Security Gateway will become active.
4. Click OK.
5. If you changed the existing setting, them install the Access Control Policy.

Tracking Options

You can configure alerts to stay updated on the status of permanent VPN tunnels.

To configure logs and alerts for VPN tunnel status:

1. In the properties of the VPN Community, open the Tunnel Management page.
2. In Tunnel down track, select the alert when a tunnel is down.
3. In Tunnel up track, select the alert when a tunnel is up.

   The alerts are configured for the tunnels that are defined as permanent, based on the settings on the page.

See status of all VPN tunnels in SmartView Monitor.

To open SmartView Monitor:

1. In SmartConsole, click Logs & Monitor.
2. Click New Tab.
3. From the bottom of this page, click Tunnel & User Monitoring.

For more details, see Monitoring Tunnels in the R80.30 Logging and Monitoring Administration Guide.