show dsl statistics
In the R81.10.X releases, this command is available starting from the R81.10.00 version.
Description
Show DSL statistics.
Syntax
|
|
Parameters
|
Parameter |
Description |
|---|---|
|
tpstc |
Indicates the TPS-TC layer. Possible values: ATM, PTM. |
|
mode |
Indicates the negotiated DSL mode. Example for a value: VDSL Annex B. |
|
status |
Indicates the status of DSL connection synchronization. Example values: Showtime, G.994. |
|
bitrate-up |
Indicates the upstream DSL bit rate. |
|
bitrate-down |
Indicates the downstream DSL bit rate. |
|
vendor |
4 hexa digits representing the vendor of the DSL chip in the peer DSLAM/MSAG (i.e. IFTN, BDCM) + 4 hex digits representing the firmware version of the vendor. |
|
power-up |
Indicates the appliance transmission power (dBm). |
|
hec-up |
Indicates the number of HEC errors counted by the peer DSLAM/MSAG. |
|
attn-up |
Indicates the upstream attenuation (dB). |
|
attn-down |
Indicates the attenuation of the power from the peer DSLAM/MSAG to the appliance (dB). |
|
rs-down |
Indicates the number of RS words that were received by the appliance in the downstream. |
|
rs-corrected-down |
Indicates the number of RS words that were corrected by the appliance in the downstream. |
|
rs-up |
Indicates the number of RS words that were received by the peer DSLAM/MSAG in the upstream. |
|
rs-corrected-up |
Indicates the number of RS words that were corrected by the peer DSLAM/MSAG in the upstream. |
|
hec-up |
Indicates the number of HEC errors counted by the peer DSLAM/MSAG. |
|
hec-down |
Indicates the number of HEC errors counted by the appliance. |
|
total-cells-up |
Indicates the number of 53 bytes (cells in the case of ATM) that were transmitted by the appliance. |
|
total-cells-down |
Indicates the number of 53 bytes (cells in the case of ATM) that were received by the appliance. |
|
configured-sra |
Indicates the seamless rate adaptation (SRA) that was configured in the appliance. Possible values: On, Off. |
|
configured-trellis |
Indicates whether trellis was enabled in the appliance configuration. Possible values: On, Off. |
|
configured-ginp |
Indicates the upstream/downstream on/off for the configured Enhanced Impulse response. Possible values: Off/Off, Off/On, On/Off, On/On |
|
configured-bitswap |
Indicates the upstream/downstream on/off for the Bit Swap configured in the appliance. Possible values: On, Off. |
|
vectoring |
Indicates the vectoring status. Possible values: 0: Vectoring Training State. 1: Showtime vectoring state, idle, not reporting errors. 2: Initial showtime vector mode state, transition to full factoring when the peer sends a vectoring configuration message. 3: Vectoring state where error samples are being reported upon peer request. 4: Vectoring is disabled. 5: DSLAM/MSAG doesn't support vectoring. |
Example Command
|
|
Sample Output
snr-down: 8.7 configured-ginp: Off/Off power-up: 7.6 rs-corrected-down: 421298 rs-corrected-up: 208 configured-sra: Off rs-up: 1610329207 configured-trellis: On total-cells-down: 2609810117 snr-up: 15.4 tpstc: PTM bitrate-up: 5024 vectoring: 5 (DSLAM is not a vectored DSLAM) vendor: IFTN:0xb206 status: Showtime rs-down: 2127995393 mode: VDSL2 Annex B hec-up: 0 bitrate-down: 48470 training: Showtime power-down: 7.7 total-cells-up: 0 hec-down: 0 attn-down: 25.9 attn-up: 0.0 configured-bitswap: Off |