Step 4 - License Installation

1. Quantum Maestro Orchestrators do not require a license.

2. Generate a Security Gateway license for each Security Appliance you connect to a Quantum Maestro Orchestrator.

   Procedure

   Prepare this summary table for all Security Appliances:

   Appliance	IPv4 Address of Sync interface (License IP Address)	MAC Address of Mgmt interface (License CK)
   Your description	IPv4 Address of the Sync interface on this appliance	MAC Address of the Mgmt interface on this appliance

   Steps:

   Step	Instructions
   A	Connect to the command line on each Security Appliance.
   B	Log in to the Expert mode.
   C	Get the IPv4 Address of the Sync interface (copy the value of "inet addr"): Note - You must generate the license for this IPv4 address. ifconfig Sync | head -n 2
   D	Get the MAC Address of the Mgmt interface (copy the value of "HWaddr"): Note - When you generate the license, you must use this MAC Address as the license CK. ifconfig Mgmt | grep Mgmt
   E	Generate the license as described in sk163323.

3. If the applicable license exists in the License Repository on the Check Point Management Server, it installs the licenses automatically.

   • If the Check Point Management Server is connected to the Internet, it pulls the licenses from the User Center.

   • If the Check Point Management Server is not connected to the Internet, then follow the procedures below.

     Note - In Dual Site, these steps install the licenses on all sites automatically.

     Part 1 - Install the license on the Security Group Member that runs as the Single Management Object (SMO)

     Step	Instructions
     A	Connect to the command line on the Security Group.
     B	Log in to the Expert mode.
     C	Get the IP address of the Sync interface on the SMO: asg_blade_config get_smo_ip
     D	Install the license for the IPv4 address of the SMO 192.0.2.X (see "Notes" below): cplic put <applicable string>
     E	Make sure the license is installed: g_cplic print

     Part 2 - Install the license on a specific Security Group Member that is not the SMO

     Important - You must follow these steps for each Security Appliance in the Security Group.

     Step	Instructions
     A	Connect to the Gaia OS of the Security Group or Quantum Maestro Orchestrator.
     B	Log in to the Expert mode.
     C	Connect to a specific Security Appliance with this command: member <Security Group ID> <Member ID> See Connecting to a Specific Security Group Member (member)
     D	Get the IPv4 Address of the Sync interface: ifconfig Sync | head -n 2
     E	Install the license for the IPv4 address of the Sync interface 192.0.2.X on this specific appliance (see "Notes" below): cplic put <applicable string>
     F	Create a copy of the $CPDIR/conf/cp.license file: cp -v $CPDIR/conf/cp.license /var/log/cp.license.copy
     G	Make sure the copy of the license file is the same as the original license file: md5sum $CPDIR/conf/cp.license /var/log/cp.license.copy
     H	Transfer the copy of the license file from this Security Group Member to the SMO: asg_cp2blades -b 1_01 /var/log/cp.license.copy
     I	Delete all data from the current license file $CPDIR/conf/cp.license on this Security Group Member: cat $CPDIR/conf/cp.license echo > $CPDIR/conf/cp.license cat $CPDIR/conf/cp.license
     J	Connect to the Security Group Member that runs as SMO: member <Security Group ID> <SMO Member ID>
     K	Add the content of the license file you copied earlier from a specific Security Group Member to the license file on the SMO: cat $CPDIR/conf/cp.license cat /var/log/cp.license.copy >> $CPDIR/conf/cp.license cat $CPDIR/conf/cp.license
     L	Wait for at least 6 minutes.
     M	Make sure the license is installed on the specific Security Group Member: g_cplic print