Viewing Bond Interfaces

Description

This command shows the configuration of bond interfaces and their subordinate interfaces.

Syntax

Shell	Command
Gaia Clish The name of the default command line shell in Check Point Gaia operating system. This is a restricted shell (role-based administration controls the number of commands available in the shell).	`show cluster bond {all \| name <bond_name>}` `show bonding groups`
Expert mode	`cphaprob show_bond [<bond_name>]` `cphaprob show_bond_groups`

Shell

Command

Gaia Clish The name of the default command line shell in Check Point Gaia operating system. This is a restricted shell (role-based administration controls the number of commands available in the shell).

show cluster bond {all | name <bond_name>}
show bonding groups

Expert mode

cphaprob show_bond [<bond_name>]

cphaprob show_bond_groups

Where:

Command	Description
`show cluster bond all` `show bonding groups` `cphaprob show_bond`	Shows configuration of all configured bond interfaces
`show cluster bond name <bond_name>` `cphaprob show_bond <bond_name>`	Shows configuration of the specified bond interface
`cphaprob show_bond_groups`	Shows the configured Groups of Bonds and their settings.

Command

Description

show cluster bond all

show bonding groups

cphaprob show_bond

Shows configuration of all configured bond interfaces

show cluster bond name <bond_name>

cphaprob show_bond <bond_name>

Shows configuration of the specified bond interface

cphaprob show_bond_groups

Shows the configured Groups of Bonds and their settings.

Examples

Example 1 - 'cphaprob show_bond'

[Expert@Member2:0]# cphaprob show_bond

                                      |Slaves     |Slaves  |Slaves

Bond name  |Mode               |State |configured |link up |required

-----------+-------------------+------+-----------+--------+--------

bond1      | High Availability | UP   | 2         | 2      | 1

Legend:

-------

UP!               - Bond interface state is UP, yet attention is required

Slaves configured - number of slave interfaces configured on the bond

Slaves link up    - number of operational slaves

Slaves required   - minimal number of operational slaves required for bond to be UP

[Expert@Member2:0]#

Member2> show bonding groups

Bonding Interface: 1

    Bond Configuration

        xmit-hash-policy Not configured

        down-delay 200

        primary Not configured

        lacp-rate Not configured

        mode active-backup

        up-delay 200

        mii-interval 100

        Bond Interfaces

            eth3

            eth4

Member2>

Description of the output fields for the "cphaprob show_bond" and "show cluster bond all" commands:

Table: Description of the output fields
Field	Description
Bond name	Name of the Gaia Check Point security operating system that combines the strengths of both SecurePlatform and IPSO operating systems. bonding group.
Mode	Bonding mode of this Gaia bonding group. One of these: `High Availability` `Load Sharing`
State	State of the Gaia bonding group: `UP` - Bond interface is fully operational `UP!` - Bond interface state is UP, yet attention is required `DOWN` - Bond interface failed
Slaves configured	Total number of physical subordinate interfaces configured in this Gaia bonding group.
Slaves link up	Number of operational physical subordinate interfaces in this Gaia bonding group.
Slaves required	Minimal number of operational physical subordinate interfaces required for the state of this Gaia bonding group to be UP.

Example 2 - 'cphaprob show_bond <bond_name>'

[Expert@Member2:0]# cphaprob show_bond bond1

Bond name:      bond1

Bond mode:      High Availability

Bond status:    UP

Configured slave interfaces: 2

In use slave interfaces:     2

Required slave interfaces:   1

Slave name      | Status          | Link

----------------+-----------------+-------

eth4            | Active          | Yes

eth3            | Backup          | Yes

[Expert@Member2:0]#

Description of the output fields for the "cphaprob show_bond <bond_name>" and "show cluster bond name <bond_name>" commands:

Table: Description of the output fields
Field	Description
Bond name	Name of the Gaia bonding group.
Bond mode	Bonding mode of this Gaia bonding group. One of these: `High Availability` `Load Sharing`
Bond status	Status of the Gaia bonding group. One of these: `UP` - Bond interface is fully operational `UP!` - Bond interface state is UP, yet attention is required `DOWN` - Bond interface failed
Configured slave interfaces	Total number of physical subordinate interfaces configured in this Gaia bonding group.
In use slave interfaces	Number of operational physical subordinate interfaces in this Gaia bonding group.
Required slave interfaces	Minimal number of operational physical subordinate interfaces required for the state of this Gaia bonding group to be UP.
Slave name	Names of physical subordinate interfaces configured in this Gaia bonding group.
Status	Status of physical subordinate interfaces in this Gaia bonding group. One of these: `Active` - In High Availability A redundant cluster mode, where only one Cluster Member (Active member) processes all the traffic, while other Cluster Members (Standby members) are ready to be promoted to Active state if the current Active member fails. In the High Availability mode, the Cluster Virtual IP address (that represents the cluster on that network) is associated: (1) With physical MAC Address of Active member (2) With virtual MAC Address. Synonym: Active/Standby. Acronym: HA. or Load Sharing A redundant cluster mode, where all Cluster Members process all incoming traffic in parallel. For more information, see "Load Sharing Multicast Mode" and "Load Sharing Unicast Mode". Synonyms: Active/Active, Load Balancing mode. Acronym: LS. bonding mode. This subordinate interface is currently handling traffic. `Backup` - In High Availability bonding mode only. This subordinate interface is ready State of a Cluster Member during after initialization and before promotion to the next required state - Active / Standby / VRRP Master / VRRP Backup (depending on Cluster Mode). A Cluster Member in this state does not process any traffic passing through cluster. A member can be stuck in this state due to several reasons. and can support internal bond failover Transferring of a control over traffic (packet filtering) from a Cluster Member that suffered a failure to another Cluster Member (based on internal cluster algorithms). Synonym: Fail-over.. `Not Available` - In High Availability or Load Sharing bonding mode. The physical link on this subordinate interface is lost, or this Cluster Member Security Gateway that is part of a cluster. is in status Down. The bond cannot failover internally in this state.
Link	State of the physical link on the physical subordinate interfaces in this Gaia bonding group. One of these: `Yes` - Link is present `No` - Link is lost

Example 3 - 'cphaprob show_bond_groups'

[Expert@Member2:0]# cphaprob show_bond_groups

                                | Required     | Bonds    | Bonds

Group of bonds name | State     | active bonds | in group | status

--------------------+-----------+--------------+----------+--------+

GoB0                | UP        | 1            |          |

                    |           |              | bond1    |   UP

                    |           |              | bond2    |   UP

Legend:

---------

Bonds in group        - a list of the bonds in the bond group

Required active bonds - number of required active bonds

[Expert@Member2:0]#

Description of the output fields for the "cphaprob show_bond_groups" command:

Table: Description of the output fields
Field	Description
Group of bonds name	Name of the Group of Bonds.
State	State of the Group of Bonds. One of these: `UP` - Group of Bonds is fully operational `DOWN` - Group of Bonds failed
Required active bonds	Number of required active State of a Cluster Member that is fully operational: (1) In ClusterXL, this applies to the state of the Security Gateway component (2) In 3rd-party / OPSEC cluster, this applies to the state of the cluster State Synchronization mechanism. bonds in this Group of Bonds.
Bonds in group	Names of the Gaia bond interfaces configured in this Group of Bonds.
Bonds status	State of the Gaia bond interface. One of these: `UP` - Bond interface is fully operational `DOWN` - Bond interface failed