fwboot bootconf

Description

Configures boot security options.

Note - These settings are saved in the $FWDIR/boot/boot.conf file.

Important - To avoid issues, do not edit this file manually. Edit this file only with the fwboot bootconf command.

Also refer to these commands:

fwboot corexl
control_bootsec

Syntax to show the current boot security options

[Expert@HostName:0]# $FWDIR/boot/fwboot bootconf

get_corexl

get_core_override

get_def

get_ipf

get_ipv6

get_kernnum

get_kern6num

Syntax to configure the boot security options

[Expert@HostName:0]# $FWDIR/boot/fwboot bootconf

set_corexl <0 | 1>

set_core_override <number>

set_def [</path/filename>]

set_ipf <0 | 1>

set_ipv6 <0 | 1>

set_kernnum <number>

set_kern6num <number>

Parameters

Parameter	Description
No Parameters	Shows the built-in help with available parameters.
`get_corexl`	Shows if the CoreXL is enabled or disabled: 0 - disabled 1 - enabled Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `COREXL_INSTALLED`.
`get_core_override`	Shows the number of overriding CPU cores. The SMT (HyperThreading) feature (sk93000) uses this configuration to set the number of CPU cores after reboot. Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `CORE_OVERRIDE`.
`get_def`	Shows the configured path and the name of the Default Filter policy file (default is `$FWDIR/boot/default.bin`). Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `DEFAULT_FILTER_PATH`.
`get_ipf`	Shows if the IP Forwarding during boot is enabled or disabled: 0 - disabled (Security Gateway does not forward traffic between its interfaces during boot) 1 - enabled Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `CTL_IPFORWARDING`.
`get_ipv6`	Shows if the IPv6 support is enabled or disabled: 0 - disabled 1 - enabled Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `IPV6_INSTALLED`.
`get_kernnum`	Shows the configured number of IPv4 CoreXL FW instances. Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `KERN_INSTANCE_NUM`.
`get_kern6num`	Shows the configured number of IPv6 CoreXL FW instances. Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `KERN6_INSTANCE_NUM`.
`set_corexl <0 \| 1>`	Enables or disables CoreXL: 0 - disables 1 - enables Notes: In the `$FWDIR/boot/boot.conf` file, refer to the value of the `COREXL_INSTALLED`. To configure CoreXL, use the `cpconfig` menu.
`set_core_override <`number`>`	Configures the number of overriding CPU cores. The SMT (HyperThreading) feature (sk93000) uses this configuration to set the number of CPU cores after reboot. Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `CORE_OVERRIDE`.
`set_def [<`/path/filename`>]`	Configures the path and the name of the Default Filter policy file (default is `$FWDIR/boot/default.bin`). Notes: In the `$FWDIR/boot/boot.conf` file, refer to the value of the `DEFAULT_FILTER_PATH`. If you do not specify the path and the name explicitly, then the value of the `DEFAULT_FILTER_PATH` is set to 0. As a result, Security Gateway does not load a Default Filter during boot. The best location is the `$FWDIR/boot/` directory.
`set_ipf <0 \| 1>`	Configures the IP forwarding during boot: 0 - disables (forbids the Security Gateway to forward traffic between its interfaces during boot) 1 - enables Note - In the `$FWDIR/boot/boot.conf` file, refer to the value of the `CTL_IPFORWARDING`.
`set_ipv6 <0 \| 1>`	Enables or disables the IPv6 Support: 0 - disables 1 - enables Notes: In the `$FWDIR/boot/boot.conf` file, refer to the value of the `IPV6_INSTALLED`. Configure the IPv6 Support in Gaia Portal, or Gaia Clish. See the R80.30 Gaia Administration Guide.
`set_kernnum <number>`	Configures the number of IPv4 CoreXL FW instances. Notes: In the `$FWDIR/boot/boot.conf` file, refer to the value of the `KERN_INSTANCE_NUM`. To configure CoreXL, use the `cpconfig` menu.
`set_kern6num <`number`>`	Configures the number of IPv6 CoreXL FW instances. Notes: In the `$FWDIR/boot/boot.conf` file, refer to the value of the `KERN6_INSTANCE_NUM`. To configure CoreXL, use the `cpconfig` menu.