Multi-Domain Log Settings - General

What can I do here?

Use this window to set disk space cleanup and alert options.

Getting Here - Getting Here - SmartConsole for Multi-Domain Server > Multi Domain > New > Multi-Domain Server > Log Settings > General Or: SmartConsole for Multi-Domain Server > Multi Domain > New > Multi-Domain Log Servers > Log Settings > General

Creating a Multi-Domain Log Server with Domain Log Servers

This section shows you how to create a new Multi-Domain Log Server and its related Domain Log Servers.

Important: Before you start this procedure, make sure that you define the physical servers as the correct server type (Secondary Multi-Domain Server or Multi-Domain Log Server) during installation. An incorrect definition can cause deployment failure.

To create a new Multi-Domain Log Server:

1. If you did not do so, install a new R80.30 Multi-Domain Log Server.

   Follow the procedures in the R80.30 Installation and Upgrade Guide.

   Make sure to define this server as a Multi-Domain Log Server in the First Time Configuration Wizard.

2. Connect with SmartConsole to the primary Multi-Domain Server - the MDS context.
3. From the left navigation panel, click Multi Domain > Domains.
4. From the top toolbar, click New > Multi-Domain Log Server.
5. Enter a unique name for this Multi-Domain Log Server.
6. Enter the IPv4 address or click Resolve IP to get the IP address from the DHCP Server.
7. Click Connect to establish SIC trust.

   Enter the same Activation Key you entered during the First Time Configuration Wizard of the Multi-Domain Log Server.

8. In the Platform section:
   • In the OS field, select Gaia
   • In the Version field, select the correct version
   • In the Hardware field, select the applicable option
9. Click OK.

To create Domain Log Servers:

1. Connect with SmartConsole to the primary Multi-Domain Server - the MDS context.
2. From the left navigation panel, click Multi Domain > Domains.
3. In the Multi-Domain Log Server column, right-click the Domain Log Server cell for each Domain and click New Domain Server.
4. Accept the default name or enter a different, unique name.
5. Enter the IPv4 address or click Resolve IP to automatically assign the IPv4 address.
6. Click OK.

   Wait for the cell to show the new Domain Log Server.

7. Configure the Security Gateways in each Domain to the send its logs to the new Domain Log Server on the Multi-Domain Log Server.

   The Domain Log Servers synchronize automatically.

The new Multi-Domain Log Server automatically synchronizes with all existing Multi-Domain Servers. The synchronization operation can take many minutes to complete, during which a notification indicator shows in the task information area.

Configuring Security Gateways to Send Logs to a Log Servers

Logs are not automatically forwarded to a Log Server. You must manually configure each relevant Security Gateway to send its logs to the new Domain Log Server.

To configure Domain Security Gateways to send logs to a Log Server:

1. Connect to the applicable Domain Management Server with SmartConsole, and then double-click the applicable Security Gateway.
2. In the Logs section, select the new Log Server from the list.

   You can delete or ignore other Log Servers in the list as necessary.

3. Click OK.
4. Configure other log settings as applicable.
5. Install Policy on the applicable Security Gateways.
6. Install the database on the Log Servers.

Deleting a Domain Log Server

To delete a Domain Log Server in SmartConsole:

1. Connect with SmartConsole to the primary Multi-Domain Server - the MDS context.
2. From the left navigation panel, click Multi Domain > Domains.
3. In the Multi-Domain Log Server column, right-click the Domain Log Server and then select Delete.

Log Management Settings

In the General view, configure these settings:

• Cleanup when free disk space is below - Start the disk cleanup procedure when available disk space is less than the specified quantity. Select to enable (default). Clear to disable.
• Enter the minimum disk space and unit of measure (Default = 5 GB).
• Run the following script before cleanup - Enter a predefined script to run before the cleanup starts.
• Send Alert when free disk space is below - Send an alert when available disk space is less that the specified quantity. Select to enable (default). Clear to disable.

  Enter the minimum disk space and unit of measure (Default = 3 GB).