In a migration and upgrade scenario, you perform the procedure on the source SmartEvent Server and the different target SmartEvent Server.
Note - To upgrade from R80.20.M1, see Upgrading a Management Server or Log Server from R80.20.M1 with Migration.
Important - Before you upgrade a SmartEvent Server:
Step |
Description |
---|---|
1 |
|
2 |
See the Upgrade Options and Prerequisites. |
3 |
Before you upgrade a dedicated SmartEvent Server, you must upgrade the applicable Management Server that manages it. |
4 |
You must upgrade your Security Management Servers and Multi-Domain Servers. |
5 |
You must close all GUI clients (SmartConsole applications) connected to the SmartEvent Server. |
Workflow:
Step 1 of 8: Get the R80.20 Management Server Migration Tool
Step |
Description |
---|---|
1 |
Download the R80.20 Management Server Migration Tool from the R80.20 Home Page SK. |
2 |
Transfer the R80.20 Management Server Migration Tool package to the current SmartEvent Server to some directory (for example, Note - Make sure to transfer the file in the binary mode. |
Step 2 of 8: On the current SmartEvent Server, run the Pre-Upgrade Verifier and export the management database
Step |
Description |
---|---|
1 |
Connect to the command line on the current SmartEvent Server. |
2 |
Log in to the Expert mode. |
3 |
Go to the directory, where you put the R80.20 Management Server Migration Tool package:
|
4 |
Extract the R80.20 Management Server Migration Tool package:
|
5 |
Important - This step applies only when you upgrade from R77.30 (or lower). Run the Pre-Upgrade Verifier (PUV).
|
6 |
Export the management database:
Notes:
|
7 |
This step applies only to R7x and R80 versions. If SmartEvent Software Blade is enabled, then export the Events database. See sk110173. |
8 |
Calculate the MD5 for the exported database file:
|
9 |
Transfer the exported database from the current SmartEvent Server to an external storage:
Note - Make sure to transfer the file in the binary mode. |
Step 3 of 8: Install a new R80.20 SmartEvent Server
Perform a clean install of the R80.20 SmartEvent Server (do not perform initial configuration in SmartConsole).
Important:
The IP addresses of the source and target R80.20 SmartEvent Servers must be the same. If you need to have a different IP address on the R80.20 SmartEvent Server, you can change it only after the upgrade procedure. Note that you have to issue licenses for the new IP address. For applicable procedures, see sk40993 and sk65451.
Step 4 of 8: On the R80.20 SmartEvent Server, import the database
Step |
Description |
---|---|
1 |
Connect to the command line on the R80.20 SmartEvent Server. |
2 |
Log in to the Expert mode. |
3 |
Make sure a valid license is installed:
If it is not already installed, then install a valid license now. |
4 |
Transfer the exported database from an external storage to the R80.20 SmartEvent Server, to some directory. Note - Make sure to transfer the file in the binary mode. |
5 |
Make sure the transferred file is not corrupted. Calculate the MD5 for the transferred file and compare it to the MD5 that you calculated on the original SmartEvent Server:
|
6 |
Go to the
|
7 |
Import the entire management database:
Notes:
|
8 |
Restart the Check Point services:
|
Step 5 of 8: Install the management database
Step |
Description |
---|---|
1 |
Connect with SmartConsole to the R80.20 Management Server that manages this dedicated SmartEvent Server. |
2 |
In the top left corner, click Menu > Install database. |
3 |
Select all objects. |
4 |
Click Install. |
5 |
Click OK. |
Step 6 of 8: Install the Event Policy
This step applies only if the SmartEvent Correlation Unit Software Blade is enabled on the dedicated R80.20 SmartEvent Server.
Step |
Description |
---|---|
1 |
Connect with SmartConsole to the dedicated R80.20 SmartEvent Server. |
2 |
At the top, click + to open a new tab. |
3 |
In the bottom left corner, in the External Apps section, click SmartEvent Settings & Policy. The Legacy SmartEvent client opens. |
4 |
In the top left corner, click Menu > Actions > Install Event Policy. |
5 |
Confirm. |
6 |
Wait for these messages to appear:
|
7 |
Click Close. |
8 |
Close the Legacy SmartEvent client. |
Step 7 of 8: Test the functionality on R80.20 SmartEvent Server
Step |
Description |
---|---|
1 |
Connect with the SmartConsole to the R80.20 SmartEvent Server. |
2 |
Make sure the configuration was upgraded correctly and it works as expected. |
Step 8 of 8: Test the functionality on R80.20 Management Server
Step |
Description |
---|---|
1 |
Connect with the SmartConsole to the R80.20 Management Server. |
2 |
Make sure the logging works as expected. |