1

Install the Gaia Operating System:

• Installing the Gaia Operating System on a Check Point Appliance
• Installing the Gaia Operating System on an Open Server

2

Run the Gaia First Time Configuration Wizard.

3

During the First Time Configuration Wizard, you must configure these settings:

• In the Installation Type window, select Security Gateway and/or Security Management.
• In the Products window:
  1. In the Products section, select Security Gateway only.
  2. In the Clustering section, select these two options:
     • Unit is a part of a cluster
     • ClusterXL
• In the Secure Internal Communication window, enter the desired Activation Key (between 4 and 127 characters long).

1

Connect with SmartConsole to the Security Management Server or Main Domain Management Server that should manage this VSX Cluster.

2

From the left navigation panel, click Gateways & Servers.

3

Create a new VSX Cluster object in one of these ways:

• From the top toolbar, click the New () > VSX > Cluster.
• In the top left corner, click Objects menu > More object types > Network Object > Gateways and Servers > VSX > New Cluster.
• In the top right corner, click Objects Pane > New > More > Network Object > Gateways and Servers > VSX > Cluster.

4

On the VSX Cluster General Properties (Specify the object's basic settings) page:

1. In the Enter the VSX Cluster Name field, enter the desired name for this VSX Cluster object.
2. In the Enter the VSX Cluster IPv4 field, enter the Cluster Virtual IPv4 address that is configured on the Dedicated Management Interfaces (DMI).
3. In the Enter the VSX Cluster IPv6 field, enter the Cluster Virtual IPv6 address that is configured on the Dedicated Management Interfaces (DMI).
4. In the Select the VSX Cluster Version field, select R80.20.
5. In the Select the VSX Cluster Platform field, select the applicable VSX Cluster mode:
   • ClusterXL (for High Availability)
   • ClusterXL Virtual System Load Sharing
6. Click Next.

5

On the Virtual Systems Creation Templates (Select the Creation Template most suitable for your VSX deployment) page:

1. Select the applicable template.
2. Click Next.

6A

On the VSX Cluster Members (Define the members of this VSX Cluster) page, add the objects for the VSX Cluster Members:

1. Click Add.
2. In the Cluster Member Name field, enter the desired name for this Cluster Member object.
3. In the Cluster Member IPv4 Address field, enter the IPv4 address of the Dedicated Management Interface (DMI).
4. In the Enter the VSX Gateway IPv6 field, enter the applicable IPv6 address.
5. In the Activation Key and Confirm Activation Key fields, enter the same Activation Key you entered during the Cluster Member's First Time Configuration Wizard.
6. Click Initialize.
7. Click OK.
8. Repeat Steps a-f to add the second VSX Cluster Member, and so on.

6B

If the Trust State field does not show Trust established, perform these steps:

1. Connect to the command line on the VSX Cluster Member.
2. Make sure there is a physical connectivity between the VSX Cluster Member and the Management Server (for example, pings can pass).
3. Run: cpconfig
4. Enter the number of this option: Secure Internal Communication.
5. Follow the instructions on the screen to change the Activation Key.
6. On the VSX Cluster General Properties page, click Reset.
7. Enter the same Activation Key you entered in the cpconfig menu.
8. Click Initialize.

7

On the VSX Cluster Interfaces (Physical Interfaces Usage) page:

1. Examine the list of the interfaces - it must show all the physical interfaces on the VSX Gateway.
2. If you plan to connect more than one Virtual System directly to the same physical interface, you must select VLAN Trunk for that physical interface.
3. Click Next.

8

On the VSX Cluster members (Synchronization Network) page:

1. Select the interface that will be used for state synchronization.
2. Configure the IPv4 addresses for the Sync interfaces on each Cluster Member.
3. Click Next.

9

On the Virtual Network Device Configuration (Specify the object's basic settings) page:

1. You can select Create a Virtual Network Device and configure the first desired Virtual Network Device at this time (we recommend to do this later) - Virtual Switch or Virtual Router.
2. Click Next.

10

On the VSX Gateway Management (Specify the management access rules) page:

1. Examine the default access rules.
2. Select the applicable default access rules.
3. Configure the applicable source objects, if needed.
4. Click Next.

Important - These access rules apply only to the VSX Gateway (context of VS0), which is not intended to pass any "production" traffic.

11

On the VSX Gateway Creation Finalization page:

1. Click Finish and wait for the operation to finish.
2. Click View Report for more information.
3. Click Close.

12

Examine the VSX Cluster configuration:

1. Connect to the command line on each VSX Cluster Member.
2. Log in to the Expert mode.
3. Run: vsx stat -v

14

Open the VSX Cluster object.

15

On the General Properties page > the Network Security tab:

1. Make sure the ClusterXL Software Blade is selected.
2. Enable the additional desired Software Blades for the VSX Cluster object itself (context of VS0).

Refer to:

• sk79700: VSX supported features on R75.40VS and above
• sk106496: Software Blades updates on VSX R75.40VS and above - FAQ
• Applicable Administration Guides on the R80.20 Home Page.

16

Click OK to push the updated VSX Configuration.

Click View Report for more information.

17

Install policy on the VSX Cluster object:

1. Click Install Policy.
2. In the Policy field, select the default policy for this VSX Cluster object.

   This policy is called: <Name of VSX Cluster object>_VSX.

3. Click Install.

18

Examine the VSX and cluster configuration:

1. Connect to the command line on each VSX Cluster Member.
2. Examine the VSX configuration:

   In Expert mode, run:

   vsx stat -v

3. Examine the cluster state in one of these ways:

   In Gaia Clish, run:

   set virtual-system 0

   show cluster state

   In Expert mode, run:

   vsenv 0

   cphaprob state

4. Examine the cluster interfaces in one of these ways:

   In Gaia Clish, run:

   set virtual-system 0

   show cluster members interfaces all

   In Expert mode, run:

   vsenv 0

   cphaprob -a if

1

Connect with SmartConsole to the Security Management Server, or each Target Domain Management Server that should manage each Virtual Device.

2

Configure the desired Virtual Devices on this VSX Cluster.

3

Configure the applicable Security Policies for these Virtual Devices.

4

Install the configured Security Policies on these Virtual Devices.

5

Examine the VSX and cluster configuration:

1. Connect to the command line on each VSX Cluster Member.
2. Examine the VSX configuration:

   In Expert mode, run:

   vsx stat -v

3. Examine the cluster state in one of these ways:

   In Gaia Clish, run:

   set virtual-system 0

   show cluster state

   In Expert mode, run:

   vsenv 0

   cphaprob state

4. Examine the cluster interfaces in one of these ways:

   In Gaia Clish, run:

   set virtual-system 0

   show cluster members interfaces all

   In Expert mode, run:

   vsenv 0

   cphaprob -a if