Health and Safety Information

Read these warnings before setting up or using the appliance.

Warning - Do not block air vents. A minimum 1/2 inch (1,27 cm) clearance is required.

Warning - This appliance does not contain any user-serviceable parts. Do not remove any covers or attempt to gain access to the inside of the product. Opening the device or modifying it in any way has the risk of personal injury and will void your warranty. The following instructions are for trained service personnel only.

Power Supply Information

The appliance contains an embedded power supply AC-DC. The 1600 appliance contains a single power supply and the 1800 contains a dual power supply.

To prevent damage to any system, it is important to handle all parts with care.

For 1800 Appliance only:

Caution, Shock hazard

Disconnect all power sources.

IMPORTANT SAFETY INSTRUCTIONS: Basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

  • Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

  • Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

  • This equipment is not suitable for use in locations where children are likely to be present.

  • Make sure to connect the power cord to a socket-outlet with a grounded connection.

  • Never open the equipment. For safety reasons, the equipment should be opened only by a qualified skilled person authorized by Check Point.

Connecting Earth Ground to Equipment

Warning - The equipment has a separate protective earthing terminal on the chassis that must be permanently

connected to earth ground to adequately ground the chassis and protect the operator from electrical hazards.

Caution - Before equipment installation begins, ensure that a service personnel has attached an appropriate grounding

lug to the grounding cable supplied.

To connect earth ground to equipment:

  1. Connect one end of the grounding cable to a proper earth ground.

  2. Place the ground lug attached to the ground cable over the protective earthing terminal.

  3. Secure the grounding lug to the protective earthing terminal with washers and screws

  4. Dress the grounding cable and ensure that it does not touch or block access to other components.

Warning - Before powering on the equipment, connect the frame of the equipment to earth. For the earthing wire, green and yellow insulation is required and the cross-sectional area of the conductor must be more than 0.75mm2 or 18 AWG.

Warning - The protective earthing terminal with washers and screws where a screw is threaded into it should not be less than twice the pitch of the screw thread, at least 3.5mm diameter; star washers or spring washers can be used.

Warning - After power is off and disconnected from the equipment, then disconnect the frame of the equipment to earth.

 

Caution - Risk of explosion if the battery is replaced by an incorrect type.

Warning - This is a class 1 Laser product. Use only IEC 60825-1 certified Optical Fiber Transceiver with minimum operating temperature at 75 degree C.(for EU)

Laser Class 1 optical transceiver shall be used only. (for UL)

For North America only

Warning message for using product in ITE environment:

Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.

For California:

Perchlorate Material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate

The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5, Chapter 33. Best Management Practices for Perchlorate Materials. This product, part, or both may include a lithium manganese dioxide battery which contains a perchlorate substance.

Proposition 65 Chemical

Chemicals identified by the State of California, pursuant to the requirements of the California Safe Drinking Water and Toxic Enforcement Act of 1986, California Health & Safety Code s. 25249.5, et seq. ("Proposition 65"), that is "known to the State to cause cancer or reproductive toxicity." See http://www.calepa.ca.gov.

WARNING:

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Declaration of Conformity

Manufacturer's Name:

Check Point Software Technologies Ltd.

Manufacturer's Address:

5 Shlomo Kaplan Street, Tel Aviv 67897, Israel

Model Number:

V-82, V-83

Product Options:

1600 / 1800 Appliance Wired

Date First Applied:

December 2020

Declares under our sole responsibility, that the products conform to the following Product Specifications:

Certification

Type

CE EN 55032:2015 + AC:2016, Class B

CE EN 55032:2012 + AC:2013, Class B

CE EN 61000-3-2:2014

CE EN 61000-3-3:2013

CE EN 55024:2010 / A1:2015

CE EN 55024:2010

FCC Part 15B

AS/NZS CISPR32

ICES-003

VCCI, V-3/2015.4 , V4/2012.04, Class B VCCI CISPR 32:2016

EMC/EMI

EN 62368-1

CB IEC 62368-1

CSA/UL_ULc 62368-1 (Ed 2/3)

AS/NZS 62368.1:2018

J 62368-1

Safety

ROHS10, REACH

Environmental

Date and Place of Issue: Tel Aviv, Israel December 2020

Testing lab

Address:

No 9 Harrison Road, Harrison Industrial Building, #05-01

Issued By:

Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Ling Kou Laboratories

Lab Address:

No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan

European Union (EU) Electromagnetic and Safety Compatibility Directive

This product is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directives 2004/108/EC and 2014/30/EU. This product is in conformity with Low Voltage Directives 2006/95/EC and 2014/35/EU. This product complies with the requirements in the Council Directives 2006/95/EC and 2014/35/EU relating to electrical equipment designed for use within certain voltage limits and the Amendment Directive 93/68/EEC.

Federal Communications Commission (FCC) Notice (US)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

Compliance Information

  1. This device may not cause harmful interference, and

  2. This device must accept any interference received, including interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canadian Department Compliance Statement

This device complies with Industry Canada ICES-003 rules.

Japan Class B Compliance Statement

This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI).

If this equipment is used in a domestic environment, radio interference may occur, in which case the user may be required to take corrective actions.

Physical and environmental reliability

Description

Operating Conditions

Vibrations and Shock Based on EN 300 019-2-3.

Temperature: 0°C ~ 40°C

Storage Conditions

Temperature: (-40)°C ~ 60°C.

Humidity: 95%, non-condensed.

Vibrations and Shock based on EN 300 019-2-1.

Transportation Conditions

Temperature: (-40)°C ~ 85°C.

Humidity: 95%, non-condensed.

Vibrations and Shock based on EN 300 019-2-2.

Product Disposal

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a distributor for designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office or your household waste disposal service.