Safety, Environmental, and Electronic Emissions Notices

Read the following warnings before setting up or using the appliance.

	Warning - Do not block air vents. A minimum 1/2-inch clearance is required.
	Warning - Many components described in this document can be damaged by Electrostatic Discharge (ESD). Follow the precautions described here and before specific procedures detailed in the document to protect static-sensitive components from ESD-related damage.

The machine can only be used in a restricted access location and has installation instructions by a skilled person.
Les matériels sont destinés à être installés dans des emplacements à accés restreint.

Before you install or remove a chassis, or work near power supplies, turn off the power and unplug the power cord.

To prevent damage to any system board, it is important to handle it with care. The following measures are generally sufficient to protect your equipment from static electricity discharge:

• This equipment must be grounded.
  Cet équipement doit être mis à la terre.
• When handling the board, to use a grounded wrist strap designed for static discharge elimination.
• Touch a grounded metal object before removing the board from the antistatic bag.
• Handle the board by its edges only. Do not touch its components, peripheral chips, memory modules or gold contacts.
• When handling processor chips or memory modules, avoid touching their pins or gold edge fingers.
• Restore the communications appliance system board and peripherals back into the antistatic bag when they are not in use or not installed in the chassis. Some circuitry on the system board can continue operating even though the power is switched off.
• Disconnect the system board power supply from its power source before you connect or disconnect cables or install or remove any system board components. Failure to do this can result in personnel injury or equipment damage.
• Avoid short-circuiting the lithium battery; this can cause it to superheat and cause burns if touched.
• Do not operate the processor without a thermal solution. Damage to the processor can occur in seconds.
• Class 1 laser product warning - A totally enclosed laser system containing a class 1 laser.

This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view.

Lithium Batter Caution

• There is a risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Installation only by a skilled person who knows all Installation and Device Specifications which are to be applied.
• Do not carry the handle of power supplies when moving to another place.
• Please conform to your local laws and regulations regarding safe disposal of lithium BATTERY.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Warning - DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

Avertissement concernant la pile au lithium

• Risque d'explosion si la pile est remplacée par une autre d'un mauvais type.
• Jetez les piles usagées conformément aux instructions.
• L'installation doit être effectuée par un électricien formé ou une personne formée à l'électricité connaissant toutes les spécifications d'installation et d'appareil du produit.
• Ne transportez pas l'unité en la tenant par le câble d'alimentation lorsque vous déplacez l'appareil.

Electrical Safety Instructions

Before turning on the device, ground the grounding cable of the equipment. Proper grounding is very important to protect the equipment against the harmful effects of external noise and to reduce the risk of electrocution in the event of a lightening strike. To uninstall the equipment, disconnect the ground wire after turning off the power. A ground wire is required and the part connecting the conductor must be greater than 6 AWG.

Consignes de sécurité électrique

• Avant d'allumer l'appareil, reliez le câble de mise à la terre de l'équipement à la terre.
• Une bonne mise à la terre (connexcion à la terre) est trés importante pour portéger l'équipement contre les effets néfastes du bruit externe et réduire les risques d'électrocution en cas de foudre.
• Pour désinstaller l'équipement débranchez le câble de mise à la terre aprés avoir éteint l'appareil.
• Un câble de mise à la terre est requis et lz zone reliant les sections du conducteur doit faire plus de 6 AWG.

ITE Room Warning

Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.

Peut étre installé dans des salles de matériel de traitement de l'information conformément à l'article 645 du National Electrical Code et à la NFPA 75.

Rack Mount Instructions

The following or similar rack-mount instructions are included with the installation instructions:

1. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature specified by the manufacturer.
2. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
3. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
4. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
5. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

For California:

Perchlorate Material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate

The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5, Chapter 33. Best Management Practices for Perchlorate Materials. This product, part, or both may include a lithium manganese dioxide battery which contains a perchlorate substance.

Proposition 65 Chemical

Chemicals identified by the State of California, pursuant to the requirements of the California Safe Drinking Water and Toxic Enforcement Act of 1986, California Health & Safety Code s. 25249.5, et seq. ("Proposition 65"), that is "known to the State to cause cancer or reproductive toxicity" (see http://www.calepa.ca.gov)

WARNING:

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Caution!

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Caution!

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

Information to user:

The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.

CE (European Union (EU) Electromagnetic Compatibility Directive)

This device is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive (2014/30/EU).

The above product conforms with Low Voltage Directive 2014/35/EU and complies with the requirements relating to electrical equipment designed for use within certain voltage limits.

Federal Communications Commission (FCC) statement for a Class A digital device or peripheral

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit that is different from the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ICES (Canadian Department Compliance Statement)

This Class A digital apparatus complies with Canadian ICES-003.

French translation: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

VCCI Compliance Statement

This section provides the compliance statement for the Voluntary Control Council for Interference by Information Technology Equipment (VCCI), which governs radio frequency emissions in Japan.

Product Disposal

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office or your household waste disposal service.

Declaration of Conformity

Name and address of the authorized trademark:	Check Point Software Technologies Ltd. 5 Shlomo Kaplan Street, Tel Aviv 6789159, Israel.
Brand name:	Check Point
Marketing models:	16000, 16000T, 26000, 26000T
Regulated models:	QL-15, QL-20, QD-10, QD-15
Manufacturer’s name:	Check Point Software Technologies Ltd.
Manufacturer’s address:	5 Shlomo Kaplan Street, Tel Aviv 6789159, Israel.
Date first applied:	May 2019

The models of the declaration described above have been assessed and found to be in compliance with the following harmonized standards, regulations, and technical references:

EMC /EMI	CE EN 55032:2015+AC: 2016 Class A EN 61000-3-2: 2014 Class A EN 61000-3-3: 2013 EN 55024: 2010 +A1: 2015 EN 61000-4-2: 2009 EN 61000-4-3: 2006 +A1: 2008 +A2: 2010 EN 61000-4-4: 2012 EN 61000-4-5: 2014 +AC: 2017 EN 61000-4-6: 2014 +AC: 2015 EN 61000-4-8: 2010 EN 61000-4-11: 2004+A1: 2017 EN 55035:2017	Electromagnetic Compatibility, Emissions requirements for information technology equipment Immunity characteristics. Limits and methods of measurement
	FCC/IC FCC: FCC Part 15, Subpart B Class A ANSI C63.4-201 ICES-003 Issue 6: 2016(updated April 2017) Class A	Information Technology Equipment - Radio Disturbance Characteristics
	VCCI VCCI-TECHNICAL REQUIREMENTS (VCCI-CISPR 32: 2016) CISPR 32: 2015 + C1: 2016	Information Technology Equipment - Radio Disturbance Characteristics
	AS/NZS _RCM AS/NZS CISPR 32: 2015 Class A CISPR32:2015+C1: 2016 Class A	Information Technology Equipment - Radio Disturbance Characteristics
Safety	IEC 60950-1:2005/AMD1:2009, IEC 60950-1:2005/AMD2:2013, EN 60950-1:2006 /A11:2009 /A1:2010 /A12:2011/ A2:2013. UL/ULc 60950-1 IEC 62368-1:2014 EN 62368-1:2014/A11:2017.	Information technology equipment. Electrical Safety requirements, LVD
RoHS	EN 50581:2012	Restriction of Hazardous Substances
WEEE	Directive 2012/19/EU	Waste Electrical and Electronic Equipment

Date and Place of issue: May 2019, Tel Aviv, Israel